| *** Spare part *** SIMATIC ET 200SP, digital input module, DI 8x 24 V DC Basic, packing quantity: 1 unit, suitable for BU type A0, color code CC01, module diagnostics |
| General information |
| Product type designation | DI 8x24 VDC BA |
| Firmware version | V1.0 |
| FW update possible | Yes |
| usable BaseUnits | BU type A0 |
| Color code for module-specific color identification plate | CC01 |
| Product function |
| I&M data | Yes; I&M0 to I&M3 |
| Engineering with |
| STEP 7 TIA Portal configurable/integrated as of version | V13 SP1 |
| STEP 7 configurable/integrated as of version | V5.5 SP3 / - |
| PROFIBUS as of GSD version/GSD revision | GSD Revision 5 |
| PROFINET as of GSD version/GSD revision | GSDML V2.3 |
| Operating mode |
| DI | Yes |
| Counter | No |
| Oversampling | No |
| MSI | No |
| Supply voltage |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 19.2 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Input current |
| Current consumption (rated value) | 8 mA; without sensor supply |
| Current consumption, max. | 70 mA; All channels are supplied from the encoder supply |
| Encoder supply |
| Number of outputs | 8 |
| Output voltage encoder supply, min. | 19.2 V |
| Short-circuit protection | No |
| 24 V encoder supply |
| 24 V | Yes |
| Short-circuit protection | Yes |
| Output current, max. | 700 mA |
| Power loss |
| Power loss, typ. | 1.6 W; 24 V, 8 inputs supplied via encoder supply |
| Address area |
| Address space per module |
| Address space per module, max. | 1 byte |
| Inputs | 1 byte |
| Hardware configuration |
| Selection of BaseUnit for connection variants |
| 1-wire connection | BU type A0 |
| 2-wire connection | BU type A0 |
| 3-wire connection | BU type A0 with AUX terminals |
| 4-wire connection | BU type A0 + external terminals |
| Digital inputs |
| Number of digital inputs | 8 |
| Source/sink input | P-reading |
| Input characteristic curve in accordance with IEC 61131, type 1 | Yes |
| Input characteristic curve in accordance with IEC 61131, type 2 | Yes |
| Input characteristic curve in accordance with IEC 61131, type 3 | Yes |
| Pulse extension | No |
| Input voltage |
| Rated value (DC) | 24 V |
| for signal "0" | -30 to +5V |
| for signal "1" | +11 to +30V |
| Input current |
| for signal "1", typ. | 6.8 mA |
| Input delay (for rated value of input voltage) |
| for standard inputs |
| — parameterizable | Yes; None / 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms (in each case + delay of 30 µs to 500 µs, depending on line length) |
| for interrupt inputs |
| — parameterizable | No |
| for technological functions |
| — parameterizable | No |
| Cable length |
| shielded, max. | 1 000 m |
| unshielded, max. | 600 m |
| Encoder |
| Connectable encoders |
| 2-wire sensor | Yes |
| — permissible quiescent current (2-wire sensor), max. | 2 mA |
| Isochronous mode |
| Isochronous operation (application synchronized up to terminal) | No |
| Interrupts/diagnostics/status information |
| Diagnostics function | Yes |
| Alarms |
| Diagnostic alarm | Yes |
| Diagnostic messages |
| Diagnostic information readable | Yes |
| Monitoring the supply voltage | Yes |
| — parameterizable | Yes |
| Monitoring of encoder power supply | No |
| Wire-break | No |
| Short-circuit | No |
| Diagnostics indication LED |
| Monitoring of the supply voltage (PWR-LED) | Yes; green PWR LED |
| Channel status display | Yes; Green LED |
| for channel diagnostics | No |
| for module diagnostics | Yes; green/red DIAG LED |
| Potential separation |
| Potential separation channels |
| between the channels | No |
| between the channels and backplane bus | Yes |
| between the channels and the power supply of the electronics | No |
| Isolation |
| Isolation tested with | 707 V DC (type test) |
| Standards, approvals, certificates |
| Suitable for safety functions | No |
| Dimensions |
| Width | 15 mm |
| Height | 73 mm |
| Depth | 58 mm |
| Weights |
| Weight, approx. | 28 g |
| last modified: | 03/28/2019 |
